Zhuoxin

SRS-2-FM/AC220 conveyor explosion-proof rope switch Product features:
& nbsp;   The protection level of the deviation switch is as high as IP65, which can prevent the entry of dust and water erosion. The inclination angle is as high as 75 °, with higher degrees of freedom. The copper tube technology structure used in this switch makes the product more precise and durable, avoiding situations where the sealing is not tight or stuck due to direct friction during the operation of the pull rope switch; Significantly extend the service life of switches; The switch cam adopts imported ABS nylon die casting, which is convenient for adjusting the switch action angle according to actual needs; The surface of the shell is exquisitely shot blasted and sprayed with plastic, which is not easy to peel off and has no odor, etc. This switch has complete functions and the quality has reached the standard< Installation and adjustment:
 & nbsp;   The deviation switch should be installed in a location with maintenance channels on both sides of the conveyor, and the installation position should ensure that maintenance personnel can operate conveniently in emergency situations< 1. The switch should be set on both sides of the conveyor belt, and the vertical rollers should be perpendicular to the edge plane of the conveyor belt, with both sides of the conveyor belt located at 1/3 of the height of the vertical rollers< The distance between the vertical roller and the normal position of the conveyor belt should be 50-100mm< 3. The quantity should be determined based on the length, type, and layout of the conveyor. Generally, it should be set at the head, tail, convex arc section, concave arc section, and in the middle position of the conveyor. (Note: When the conveyor is long, one pair can be set every 30-35 meters in the middle of the conveyor)
 & 4. The deviation switch should be connected to the middle frame of the conveyor through an installation bracket. The opening bracket should be welded to the conveyor frame after the conveyor installation is completed, and the switch and switch bracket should be fixed with bolts. Attention
1. First cut off the main power supply, and then use a multimeter to measure the live wire. The switch must be installed at one end of the live wire. 2. Cut the live wire in a suitable place, and there are two joints, and the pull switch also has two joints. 3. Peel off the two joints of the live wire and expose the metal wire, and connect them to either of the two joints of the switch. 4. Cut off the excessively long metal wire at the connected joint to prevent two metal wires from colliding and short circuiting. 5. Loosen the cover of the pull switch and you can see a metal shaft with a hole at one end. 6. There is also a hole on the side of the plastic casing of the pull switch. First, pass the pull wire through the opening of the plastic casing to introduce the pull wire into the pull switch. Then, insert one end of the introduced pull wire into the shaft and tie a knot. Shorten the excessively long pull wire after tying. 7. Rotate the cover of the cable switch to prevent electric shock< br/>YHPK-1，SSG-12-30，SSG-10-45，SSG-20-35，XLLPP-J， XLLPP-D，PPKG-12-30，PPKG-10-45，PPKG-20-35，HFPPKG-12-30，HFPPKG-10-45，HFPPKG-20-35，HFKPT1-12-30，HFKPT1-10-45，HFKPT1-20-35，HFKPT1-N，KDPE3-KH，KLT1-1 2，KLT1A1-1 2，KLT2-1 2，KLT2A-1 2，KLT2A2-1 2，KPT1-12-30，LKLT1-12-30，WHKL，WHKP-12-30，YTJKPT1，YTJKPT2，YWPPH，CRS-2D，CRS-2DA，HESEX011，PW-12-30，PW-10-45，PW-20-35，YF/PK，KPT1-12-30，KPT1A-12-30，PPKG-12-30，PPKG-10-45，PPKG-20-35，HFPPKG-12-30，HFPPKG-10-45，HFPPKG-20-35，HFP，JYB/PK，ROS-2D，SXLSKG-1，SXLSKG-2，DPK-12-30，DPK-10-45，DPK-20-35