Tilt switch 21-39-50FTsx21-39-50FT
When the tilt switch with a vertical suspension of 21-39-50FT is subjected to external force and deviates from the vertical position by more than 15 degrees, the mercury contacts inside the switch will act and the normally closed contacts will open. After the external force is removed, the tilt switch returns to the vertical state, and the mercury contacts close again. Use the changes in the opening and closing of the internal contacts of the tilt switch to determine the working condition of the protective equipment, and take timely measures to achieve the purpose of safety protection.
- Tilt switch 21-39-50FT
- ZHUOXIN
- 24-380v
- IP65
- TT, Paypal, Credit card, Western union
- +86-15163766288
- When the tilt switch with a vertical suspension of 21-39-50FT is subjected to external force and deviates from the vertical position by more than 15 degrees, the mercury contacts inside the switch will act and the normally closed contacts will open. After the external force is removed, the tilt switch returns to the vertical state, and the mercury contacts close again. Use the changes in the opening and closing of the internal contacts of the tilt switch to determine the working condition of the protective equipment, and take timely measures to achieve the purpose of safety protection.
Description
Tilt Switch 21-39-50FT Tilt Switch 21-39-50FT Tilt Switch 21-39-50FT Technical Parameters
1. Rated Contact: 24V/220VAC/2A
2. Rated Temperature: -20~100 ℃ (customizable at 200 ℃)
3. Shell Material: Cast Iron
4. Cable Length: 6000mm (customizable) Features: The tilt switch can be used with a probe alone or in combination with a control device. The alarm output time is adjustable, and the control device has an adjustable delay line of 0-10 seconds to avoid false action caused by instantaneous tilt of the tilt switch. The normal/alarm position can be set, and there is a jumper in the control device that can set the switch to a normal or inclined state. It is sturdy and corrosion-resistant, and easy to install. The control device is a printed circuit board structure. All probes are equipped with installation accessories. Usage:
* Chute or adapter blockage detector
* Conveyor belt deviation detector
* Application range of dump machine discharge probe
? Blockage detection at chutes or adapters
? Detection of conveyor belt deviation
? Dumping machine unloading detection
? SN04-P SN04-N2 TL-N10MY1 TL-N10MF1 JK-G-K25 LK20-4K-G NBN15-30GM60-W0 NBN15-30GM50-Z1 NBB10-30GM60-Z1 NBN8-18GM50-E2 NBB5-18GM50-Z0 NBN4-12GM40-Z021-39-50FT is a pressure cast iron tilt switch widely used to detect the upper limit level of bulk materials (such as powder, particles, blocks) in silos or transfer chutes. When the input of materials increases and the switch part tilts about 17 degrees, the switch inside the material flow will act and output a contact signal.
1. Rated Contact: 24V/220VAC/2A
2. Rated Temperature: -20~100 ℃ (customizable at 200 ℃)
3. Shell Material: Cast Iron
4. Cable Length: 6000mm (customizable) Features: The tilt switch can be used with a probe alone or in combination with a control device. The alarm output time is adjustable, and the control device has an adjustable delay line of 0-10 seconds to avoid false action caused by instantaneous tilt of the tilt switch. The normal/alarm position can be set, and there is a jumper in the control device that can set the switch to a normal or inclined state. It is sturdy and corrosion-resistant, and easy to install. The control device is a printed circuit board structure. All probes are equipped with installation accessories. Usage:
* Chute or adapter blockage detector
* Conveyor belt deviation detector
* Application range of dump machine discharge probe
? Blockage detection at chutes or adapters
? Detection of conveyor belt deviation
? Dumping machine unloading detection
? SN04-P SN04-N2 TL-N10MY1 TL-N10MF1 JK-G-K25 LK20-4K-G NBN15-30GM60-W0 NBN15-30GM50-Z1 NBB10-30GM60-Z1 NBN8-18GM50-E2 NBB5-18GM50-Z0 NBN4-12GM40-Z021-39-50FT is a pressure cast iron tilt switch widely used to detect the upper limit level of bulk materials (such as powder, particles, blocks) in silos or transfer chutes. When the input of materials increases and the switch part tilts about 17 degrees, the switch inside the material flow will act and output a contact signal.
Tags
Get the latest price? We'll respond as soon as possible(within 12 hours)