Zhuoxin

Stainless steel rope switch LXA-02GKH-T1-B Stainless steel rope switch LXA-02GKH-T1-B Stainless steel rope switch LXA-02GKH-T1-B Belt conveyor rope switch installation and wiring: (1) Installation  Users can create a self-made installation bracket based on the installation dimensions indicated by the external structure, or they can order it from our company. Fix the switches on both sides of the tape conveyor, install them in pairs, and meet the following requirements: 1. During installation, the product should be lower than the tape (its height should be convenient for on-site personnel to use) and fixed on both sides of the tape conveyor along the line. The distance between each pull rope switch should be about 40 meters. 2. Tie the pull rope to the swing arm of the switch body, fix it with a rope clip, and first install support rings on both sides of the switch nearby. Then install support rings every 3 meters to avoid excessive deflection and ensure the normal use of the switch. 3. Under the premise of meeting the normal operation of the switch, try to tighten the ropes on both sides as much as possible and minimize the vertical deflection of the rope. 4. For slope tape machines, the length of the pulling rope and the switching distance should be shortened as appropriate. （2） Wiring; Lead out a four core rubber sleeve cable at the outlet, which is red, blue, yellow, and black. Among them, red and blue are the outgoing lines of the dynamic break point. Yellow and black represent the outgoing lines of the dynamic closing contact. The purpose of the bidirectional rope switch for mining: The bidirectional rope switch is commonly known as an emergency stop switch. When the belt conveyor needs to be stopped on site, the conveyor can be stopped by a switch action. The bidirectional pull rope switch is widely used in factories and mines with belt conveyors, such as steel, cement plants, power plants, and mines. This product is installed on both sides of the belt conveyor and is a protective switch for emergency accidents of the belt conveyor. It pulls the steel wire rope at any point within the operating distance of the switch, cuts off the running circuit, and stops the entire line, achieving protection for the belt conveyor and personal safety. It is divided into manual and automatic types. After manual action, it self sells and has warning signs indicating that it must be manually reset. Automatic automatic reset, can stop the emergency rope switch by pulling the rope sensing gas at will in case of an emergency. Technical specifications: working voltage: AC220V, action angle: 25 °, contact capacity: AC220V; 3A Extreme angle: 75 ° Contact form: double break point 1 normally open 1 normally closed Protection level: IP65 Service life: 100000 times heavy& nbsp;   Quantity: 2.5Kg. T3Z 068-11YRS Emergency Stop Pull Cord T3Z 068-11YRG Low Operating Power Pull Cord T3Z 068-22YR Emergency Stop Pull Cord Switch Mechanical Parameters T3Z 068-11YR Limit Switch Safety Pull Cord Switch LLJZS71-11VO Sound and Light Alarm \ HQSG-116/BSICK/Schke Optoelectronic Switch CDD-40NKPT1-12/30 Runaway Switch Proximity Switch/GH1-407QC/NPN/One Open and One Close LJA41M-3005PT-G With Connection Wire Proximity Switch Ni15-M30-OP6L Inductive Proximity Switch Proximity Switch Model: Ni8-G18-OP6LNi15-M30-CP6L Yike Proximity Switch Switch GAM4-12GM-D1 Inductive Proximity Switch FBK-Q450H-B Explosion proof Pull Wire Switch Pull Rope Switch FJ-PP-B-J-II, 0-380VLFB-I, LFB-II Thin Film Level Meter Working Voltage Level Meter LFB-11-220V-1AYS-05C Crown Block Collision Prevention Sound and Light Alarm YS-300M High Power Voice Sound and Light Alarm DBJ-1Z, DBJ-1J explosion-proof sound and light alarm TGSG-01 sound and light alarm HDSL-135L heavy load sound and light electronic buzzer BC-8UYH-5YH-FM integrated sound and light alarm YH-1 alarm, YB-BFBBC-3BF electronic sound and light alarm integrated sound and light alarm, MY-TBJ-150BC-8C volume adjustable sound and light alarm BC-8T sound and light alarm BC-8K. LED long light/flashing volume BC-8 sound and light alarm YM325B-A alarm series SJ-2L, SG-8, ML-20 marine sound and light alarm TRM-220 rotating buzzing and flashing warning light, alarm buzzer TRM-12 alarm TBJ-150C overhead crane sound and light alarm suitable for outdoor use TBJ-150G sound and light alarm TBJ-150Y safety accident sound and light alarm TBJ-150 explosion-proof sound and light alarm TBJ-100CY coke machine and other walking equipment special sound and light alarm TBJ-10TBJ-100 sound and light alarm HFKLT2-II with self-locking protection bidirectional rope opening TURCK/Turck proximity switch BI15U-Q20-AP6FM6 D-116 helmet type sound and light alarm FMD-116A snail type sound and light alarm Q-TC01-24-G parking switch, mining general JS-B speed detection device magnet KY35M-2 control magnetic steel KY35M-Z | NS pole magnetic two piece with automatic drainage AC2010-02D, AC3010-02D, AC3010-03D, AC4010-03D, AC4010-04D, AC4010-06D, AC5010-06D, AC5010-10D automatic drain SA402, AD402, NP-16B, NP-II, ZDFS, SDV-400-A air source processor new AC20-02, AC20-02D,AC20-02E，AC20-02DE，AC30-02，AC30-02D，AC30-02DE，AC30-03，AC30-03D，AC30-03DE，AC40-04，AC40-04D，AC40-04DE，AC50-06，AC50-06D，AC50-06DE，AC50-10，AC50-10D，AC50-10DE，AC20A-02，AC20A-02D，AC20A-02E， AC20A-02DE，AC30A-02，AC30A-02D，AC30A-02E，AC30A-02DE，AC30A-03，AC30A-03D，AC30A-03E，AC30A-03DE，AC40A-04，AC40A-04D，AC40A-04E，AC40A-04DE，AF20-02，AF20-02D，AF30-02，AF30-03D，AF40-04，AF40-04D，AF50-06，AF50-06D，AF50-10，AF50-10D，AR20-02，AR20-02E，AR30-02，AR30-02E，AR30-03，AR30-03E，AR40-04，AR40-04E，AR50-06，AR50-06E，AR50-10，AR50-10E，AL20-02，AL30-02，AL30-03，AL40-04，AL-50-06，AL50-10，AW20-02，AW20-02D，AW20-02E，AW20-02DE，AW30-02，AW30-02D， AW30-02E，AW30-02DE，AW30-03，AW30-03D，AW30-03DE，AW40-04，AW40-04D，AW40-04E，AW40-04DE