Zhuoxin

JNCA-D1A Permanent Magnet Safety Door Lock Specification Parameters JNCA-D1A Permanent Magnet Safety Door Device End Beam Boarding Gate Rated Current 6A, also known as Permanent Magnet Safety Door Device, is a new product for crane permanent magnet anti-collision safety door device. It is designed to address safety hazards in on-site use of crane end beam boarding gates and can replace door bolts and safety switches on end beam boarding gates. It has a long service life, strong seismic resistance, simple installation, no need to change the electrical control system, and prevents safety hazards. This product is equipped with a strong magnetic device. When the end beam boarding gate is close to this product, the strong magnetic device tightly attaches the boarding gate to the device, while outputting signals to the electrical control system. The synchronization between locking the door and signal output makes it easier for staff to operate and pass through the end beam boarding door. Explosion proof sound and light alarm BBJ-220 tear switch BZL-220B 380V 3AIP66 explosion-proof rope switch EX-FKT2AC2220V slip switch SMS-B1/BIP66 permanent magnet collision safety door device INCHI-CMS/D1B permanent magnet collision safety door device INCHI-CMS/D1A proximity sensor SMS-GKADΦ 30 DC24VZKG-20 Coal Blocking Sensor Chain Breaker Protector KCSP-CR RF Admittance Level Switch: JDSPSCEL600MYZ 220V 600mm Temperature Resistant 400 ℃ Proximity Switch E13C-Z304PCX Diameter 12mm Permanent Magnet Collision Safety Door Device INCHI-COM/D1A Permanent Magnet Collision Safety Door Device INCHI-COM/D1B Technical Parameters: JNCA-D1A Permanent Magnet Safety Door Device End Beam Boarding Gate 1 Rated Current: 6A2 Rated Circuit Voltage: 110-380V3 Environmental Temperature: -20 ℃ -+65 ℃ 4 Relative Humidity:< 95% (+25 ℃, 5 is suitable for environments with severe dust, including conductive powder. 6 is suitable for places with moderate or lower vibration or impact. 7. Housing protection level: IP67. Usage: Fix the safety door device on the angle steel with M8 screws and wire it according to the requirements. Voltage naming method: Permanent magnet safety door lock JNCH-D1A (110-380V), permanent magnet safety door lock JNCH-D1B (12-36V). When the magnet passes through the mining proximity switch from one direction, the output contact is closed and held, and then the output contact is disconnected and held again through the proximity switch from the other direction. 1. Technical index a: Rated voltage of permanent magnet device: 380V/15A (resistance). Sexual load); b， Contact method of permanent magnet device: normally open; Normally closed c, large relative velocity between permanent magnet device and magnetic steel: 15m/s; d， The suction distance between the permanent magnet device and the magnetic steel is ≤ 120?, Release distance ≥ 200? (Magnetic steel surface magnetic field ≥ 1300GS. 2. Environmental conditions and precautions for use a, ambient temperature: -5 ℃~+60 ℃; b, atmospheric pressure: 80KPa~106KPa;); c， Relative humidity: ≤ 95% (+25 ℃); d, atmospheric pressure: 80KPa~106KPa; e， In situations where there is no significant vibration or impact; f， In situations where there is explosive mixture underground in coal mines, but there is no corrosive damage to insulation. g， Sealing products are strictly prohibited from being knocked or modified during operation to affect their explosion-proof performance. h， The surface magnetic field of the matching magnetic steel must be ≥ 1300GS. Position control switch XFM30-A15AK-X220VAC sound and light alarm | SGBJ022 sound and light alarm IIX-100BJNCA-D1A permanent magnet safety door lock specification parameters