Zhuoxin

The pouring type magnetic proximity switch KGE1-1AF is a powerful magnetic switch used for shaft hoists, suitable for hoists. It is mainly used in mine shafts as a signal for cage positioning and an indicator of lifting degree and degree. Its application is very extensive, and when used in conjunction with corresponding magnets, it can sense the detected object at 250mm, 360mm, and 500mm. This product has a very high positioning and a very long sensing distance, making it an excellent choice among similar products and can be used as a product. Performance parameters of pouring type magnetic proximity switch KGE1-1AF: Contact parameters: 110V 127V; 220V   2A
Power supply voltage: 110V (& plum; 10), 50Hz
Induction magnetic field strength: 10GS
Induction distance: 250-50mm
Speed response: can meet a speed response of 30M/s.
Number of contacts: two sets of normally open and normally closed points
Working frequency: The lifespan of the contacts can reach 100000 times. Product appearance: The appearance should be designed aesthetically pleasing, the appearance should be clean, and the surface of the sealed colloid should be flat and shiny. The pouring type magnetic induction switch KGE1-1AF uses connecting cables: check whether the wires inside the connecting cables are copper wires or tin plated wires. Tin plated wires have much better performance than copper wires and are also more expensive (10 core cables). Generally, cheap copper core wires are used to save costs. Reaction of magnetic switch to magnet: When the magnetic switch is used in combination with TS250 magnet, the interaction between the magnet and the magnetic switch is 245mm~255mm. Products larger than 260mm and smaller than 240mm are not qualified. The influence of geomagnetism on magnetic switches: A good magnetic switch needs to have good capabilities, and one of the main indicators for judgment is the influence of geomagnetism on magnetic switches. The testing method is as follows: using the TS250 magnet as an example, point the head of the magnetic switch towards the geographical south and geographical north respectively, and then align the S-pole row of the TS250 magnet with the head of the magnetic switch for testing; In both cases, the large distance between the magnetic switch and the TS250 magnet should be within the range of (245mm, 255mm), with an interval of 10mm. The shorter the interval, the smaller the influence of geomagnetism, and in good cases, the interval is around 5mm. If the interval is greater than 15mm under the influence of geomagnetism, it is not a qualified and good product. The pouring type magnetic induction switch KGE1-1AF unipolar magnetic switch has a positioning window of *. The establishment of a positioning window can significantly improve the positioning of the magnetic switch on the cage. The discrimination method for positioning window: When a magnet approaches the magnetic switch from far to near, the distance between the magnet and the magnetic switch is represented by L when L> At 255mm, the magnetic switch does not operate, and at 100mm< L<255mm， The magnetic switch is in the active state when L< 100mm magnetic switch in non operating state; This can control the installation position on site and improve the positioning of the magnetic switch. So when installing a magnetic switch, the distance range between the magnet and the magnetic switch should be (120mm, 220mm). There are two ways to use it:; 1. The usage method of wire rope magnetic field source is to use a wire rope magnetizer and demagnetizer in conjunction with this usage. First, choose a place where the swing of the hoist wire rope is relatively small, such as under the drum, guide wheel, or crown wheel. Install the magnetic switch next to the wire rope, with the switch end face sensor facing the wire rope, and the distance between the switch end face and the rope is less than 50mm. Then use a wire rope magnetizer to magnetize at the corresponding position on the wire rope. During the lifting process, when the magnetization section of the steel wire rope reaches the magnetic switch position, the switch acts and sends out signals such as deceleration. Its application principle is similar to a magnetic tape recorder, which records the position signal on a steel wire rope. During operation, the magnetic switch detects the recording point and sends out a position signal. Shandong Zhuoxin Machinery Co., Ltd. is a company mainly engaged in industrial control electrical appliances, including proximity switches, photoelectric switches, Hall IC Hall switches, Hall components, two-stage deviation switches, bidirectional rope switches, speed detectors, belt slip switches, anti rotation material levels, belt longitudinal tear switches, mining magnetic wellbore switches, tilt switches, chute blockages, sound and light warning devices, limit switches, travel switches, elevator switches, elevator weighing sensors, solenoid valve coils, gear sensors, temperature resistant passive feedback sensors, cold and hot metal sensors, speed rotation monitoring sensors, speed sensors, proximity sensors, photoelectric sensors, contactless magnetic switches, magnetic proximity switches, belt conveyor control cabinets, etc. We collect, trial produce, and develop industrial control electrical appliances. Manufacturing, sales and integration. Casting type magnetic induction switch model: KGE1-1P KGE1-1T、KGE-1AP,KGE1-1F ,TCK-1AP
TCK-1P、TCK-2P、TCK-3P、TCK-4P
TCK-1,TCK-2,TCK-3,TCK-4
TCK-1T、TCK-2T、TCK -3T、TCK -4TKGE1-1AP-SK、 Magnet model: S-250, TS-360，TS-500